Indoor Rowers There are 141 products.

per page
Showing 51 - 75 of 141 items
  • £14.00

    For use on all Dynamic Indoor Rowers. See more info.

    £14.00
  • £12.50

    For use on all Concept2 Indoor Rowers. Replacement seat top. 12" wide, 10" deep, 1½" thick, with contours for pelvic bones and tailbone. Mounting screws and lock washers (four each) included. Original equipment on Model C, D, E and Dynamic Indoor Rowers. Can be retrofitted on all Model B and most Model A Indoor Rowers, replacing the original "kidney"...

    £12.50
  • £12.00

    The Android Connection Kit is used to connect a PM3, PM4 or PM5 to an Android device for using software such as ErgData. 

    £12.00
  • £12.00

    For use with Model C, D, E and Dynamic Indoor Rowers. One of the 3-1/4 inch wide top seat rollers (two per machine; sold individually) that runs on the stainless steel track on the monorail. Mounting hardware that holds the roller on the seat frame is not included, because it can usually be re-used. If you need the hardware, order part number 1728...

    £12.00
  • £12.00

    Let’s face it: the backside works hard during rowing. If you prefer a bit more padding, try our seat pad. Made from 12mm textured rubber, this provides the comfiest row around with cut out sections in the middle for the pelvis and at the rear to accommodate the coccyx. The seat pad can be easily transferred between machines.

    £12.00
  • £11.00

    For use with the Model A and B Indoor Rower (Ergometer) only.  This is the heel rest for the Model A and B Indoor Rower (Ergometer). Includes two screws, washers and wing nuts. See more info.

    £11.00
  • £10.09

    For use with Model C and original Model D Indoor Rowers. This is the Framelock Kit for all Model C and original Model D Indoor Rowers. It includes the axle, the framelock, the framelock cord, two screws, two washers and a hexkey tool.

    £10.09
  • £9.00

    For use with Model A and B Indoor Rowers. This is one of the 2¼" wide seat rollers that run on the top and bottom of the stainless steel tube monorail. Includes the seat roller bearings (sealed inside). Does not include mounting hardware. If you also need mounting hardware, order part number 378 instead. See more info.

    £9.00
  • £9.00

    This special nut tool is required to replace the flywheel axle sprockets on Model C, D or E Indoor Rowers. Model D and E Axle and Sprocket Replacement

    £9.00
  • £7.50

    For use with Model A and B Indoor Rowers. This is the right footboard for the Model A and B Indoor Rower (Ergometer). Comes predrilled and includes the three footboard screws and nuts.

    £7.50
  • £7.50

    For use with Model A and B Indoor Rowers. This is the left footboard for the Model A and B Indoor Rower (Ergometer). Comes predrilled and includes the three footboard screws and nuts.

    £7.50
  • £7.00

    For use with Model C Indoor Rowers. This is the lever and damper (shutter) on the side of the flywheel housing that slides up and down to change the airflow through the flywheel. Less air through the flywheel (setting = 1) means less drag when rowing; more air through the flywheel (setting = 10) means more drag. Fits Model C Indoor Rowers only. See more...

    £7.00
  • £6.00

    For use with Model C, D and E Indoor Rowers. This is the 12´ 6" long elastic shock cord (or bungee cord) that recoils the chain on recovery. If your chain recoils slowly—or not at all—between strokes, then you should inspect your existing shock cord. See more info.

    £6.00
  • £5.00

    This is the part of the indoor rower that connects to the main box frame on one end and the monitor arm on the other end. This is the right side. For use on all Model C Indoor Rowers and on Model D Indoor Rowers manufactured from July 2003–2006.

    £5.00
  • £5.00

    This is the part of the indoor rower that connects to the Performance Monitor on one end and the chain guide brackets on the other. For use on all Model C and Model D Indoor Rowers. See more info.

    £5.00
  • £5.00

    This is the part of the indoor rower that connects to the main box frame on one end and the monitor arm on the other end. This is the left side. For use on all Model C Indoor Rowers and on Model D Indoor Rowers manufactured from July 2003–2006. See more info.

    £5.00
  • £5.00

    For use with a PM5, PM4 or PM3, the Smartphone Cradle slides onto the top of the PM to provide a place to set your mobile device while using the indoor rower or SkiErg. See more info.

    £5.00
  • £5.00

    For use with Model C, D, E and Dynamic Indoor Rowers. This is one of the small bottom seat rollers (two per machine; sold individually) that runs under the top edge of the monorail. Includes mounting hardware (nut, bolt and spacers) that hold the roller on the seat frame. See more info.

    £5.00
  • £4.00

    For use with Model C, D, E and Dynamic Indoor Rowers. This is one of the small bottom seat rollers (two per machine; sold individually) that runs under the top edge of the monorail. Does not include the mounting hardware (nut, bolt and spacers) that hold the roller on the seat frame, because it can usually be reused. If you need the hardware, order part...

    £4.00
  • £4.00

    For use with the Model C, D and E Indoor Rowers. This is the 2" x 2" x 3/4" metal traveling pulley assembly with a chain idler pulley included. The chain and shock cord come together at the traveling pulley, and the traveling pulley moves back and forth inside the indoor rower on every stroke. One per machine. See more info.

    £4.00
  • £4.00

    For use with Model A, B, updated D, E, Dynamic Indoor rowers and the black SkiErgs manufactured from August 2014–present. This is the right caster wheel.

    £4.00
  • £4.00

    For use with Model A, B, updated D, E, Dynamic Indoor rowers and the black SkiErgs manufactured from August 2014–present. This is the left caster wheel.

    £4.00
  • £3.50

    This tube houses the 5-1/2 inch bolt that holds the monorail hangar assembly together. For use on all Model C Indoor Rowers and on Model D Indoor Rowers manufactured from July 2003–2006. Order two per machine.

    £3.50
  • £3.00

    For use with updated Model D, Model E and Dynamic Indoor Rowers (made after July 21, 2006) only. If your indoor rower was made before July 21, 2006, order part number 1501 instead. Two per machine. Sold individually.

    £3.00
Showing 51 - 75 of 141 items