No products
Prices are tax included
Product successfully added to your shopping cart
There are 0 items in your cart. There is 1 item in your cart.
Model D, Updated
General Information
Parts listed here are compatible with Model D Indoor Rowers manufactured from July 31, 2006–present (serial numbers 073106–present).
Model D, Updated There are 112 products.
-
£3.30
Upper Die Cast Hanger—Updated Model D, E
For use with Model D Indoor Rowers manufactured from November 2006–present and Model E Indoor Rowers. See more info.
£3.30 -
£3.30
Lower Die Cast Hanger—Updated Model D, E
For use with Model D Indoor Rowers manufactured from November 2006–present and Model E Indoor Rowers. See more info.
£3.30 -
£3.30
Shock Cord Pulley
For use with Model C, D and E Indoor Rowers. This is a 3-3/8 inch diameter pulley that the shock cord (part number 1731) runs over inside the Concept2 Indoor Rower. There are four per machine. Sold individually. See more info.
£3.30 -
£3.30
Footstretcher Cover, Left
For use with the updated Model D, Model E and Dynamic Indoor Rowers. Left footstretcher cover. The flextfoot piece (part number (part number 1063, sold separately) fits into this part to make the complete footstretcher assembly. Footplate/Flexfoot Assembly Diagram
£3.30 -
£3.30
Footstretcher Cover, Right
For use with the updated Model D, Model E and Dynamic Indoor Rowers. Right footstretcher cover. The flextfoot piece (part number (part number 1063, sold separately) fits into this part to make the complete footstretcher assembly. Footplate/Flexfoot Assembly Diagram
£3.30 -
£3.30
Footstrap
For use with updated Model D, Model E and Dynamic Indoor Rowers. Replacement nylon footstrap with buckle, approximately 30" long by 1" wide with a screwhole drilled approximately 9" from the buckle end. Two per machine. Sold individually. Model D/E Flexfoot Assembly Diagram
£3.30 -
£3.00
Chain Guide—Model C, D, E
For use on the Model C, D and E Indoor Rower. This is the part that the chain passes through before entering into the flywheel assembly. See more info.
£3.00 -
£2.70
Monorail Bolt Support—Updated Model D, E
For use with Model D Indoor Rowers manufactured from November 2006–present and Model E Indoor Rowers. See more info.
£2.70 -
£2.70
Hanger Shaft, threaded
For use with all Model D and Model E Indoor Rowers manufactured from August 2006–present.
£2.70 -
£2.40
17mm Bearing—Model C, D, E
For use on all Model C, D and E Indoor Rowers. This is the 17mm bearing located outside of the flywheel. The corresponding bearing cup (part number 1012) is sold separately. See more info.
£2.40 -
£2.20
Upper Hanger—Updated Model D, E
For use with Model D Indoor Rowers manufactured from November 2006–present and Model E Indoor Rowers. See more info.
£2.20 -
£2.20
Mouse—Updated Model D, E
For use with Model D Indoor Rowers manufactured from November 2006–present and Model E Indoor Rowers. See more info.
£2.20 -
£2.20
-
£2.20
-
£2.20
Foot Cap
For use with Model A, B, C, D, E and Dynamic Indoor Rowers. This is the hard plastic cap that goes on the rear and/or front metal legs of the indoor rower to protect your carpet or floor and keep the machine from sliding back and forth while you row. Two to four per machine, depending on age and indoor rower model. Sold individually. See more info.
£2.20 -
£2.20
-
£2.00
Technique Label—RowErg
For use on RowErgs and Model C, D and E Indoor Rowers. This label illustrates proper rowing technique. Place just above the handle hook.
£2.00 -
£1.90
R8 Bearing—Model B, C, D, E, Dynamic
For use on all Model B, C, D, E and Dynamic Indoor Rowers. This is the R8 bearing located outside of the flywheel. The corresponding bearing cup (part number 1013 or 258 depending on which model you have) is sold separately. See more info.
£1.90 -
£1.80
Chain Idler Pulley
For use with Model C, D and E Indoor Rowers. These are the 1¼" diameter urethane pulleys that the chain runs over inside the indoor rower. There are two per machine: one is part of the traveling pulley (part number 1756); the other is mounted on a stationary axle and has two chain idler spacers (part number 1305) to keep it properly aligned. See more info.
£1.80 -
£1.30
Rear Bumper—Model C, D, E
For use on the Model C, D and E Indoor Rower. This is the bumper for the rear of the monorail. See more info.
£1.30 -
£1.20
Handle Hook
For use with Model C, D and E Indoor Rowers. This is the handle hook used on the Models C, D and E Indoor Rower. To store the handle long-term, place the handle up against the flywheel housing. For ease of use before or during a workout, placing the handle in the handle hook puts the handle within easy reach. Includes hardware.
£1.20 -
£1.20
Slotted Chain Swivel Bushing—Model C, D, E
For use on all Model C, D and E Indoor Rowers. This swivel bushing is installed at the swivel/handle end of the chain to prolong chain life and provide smoother rowing. See more info.
£1.20 -
£1.20
Handle U-bolt
For use with the handle on all models of indoor rowers. Connects the handle to the chain. The corresponding nuts are part number 240 for a Model A, B or C and part number 1235 for Model D, E and Dynamic.
£1.20 -
£1.10
Compression Member
For use with Model D Indoor Rowers manufactured from November 2006–present and Model E Indoor Rowers. See more info.
£1.10 -
£1.10
